Average

SCPI Commands

FETCh:CDMA:MEASurement<Instance>:MEValuation:LIST:SEGMent<Segment>:OBW:AVERage
CALCulate:CDMA:MEASurement<Instance>:MEValuation:LIST:SEGMent<Segment>:OBW:AVERage

class Average

Average commands group definition. 2 total commands, 0 Sub-groups, 2 group commands

class CalculateStruct

Response structure. Fields:

• Reliability: int: decimal ‘Reliability Indicator’. In list mode, a zero reliability indicator indicates that the results in all measured segments are valid. A non-zero value indicates that an error occurred in at least one of the measured segments.

• Seg_Reliability: int: decimal The segment reliability indicates whether one of the following exceptions occurred in this segment: 0: No error 3: Signal overflow 4: Signal low 8: Synchronization error If a combination of exceptions occurs, the most severe error is indicated. Range: 0 | 3 | 4 | 8

• Obw: float: float Occupied bandwidth Range: 0 MHz to 8 MHz (SDEViation 0 MHz to 4MHz) , Unit: Hz

class FetchStruct

Response structure. Fields:

• Reliability: int: decimal ‘Reliability Indicator’. In list mode, a zero reliability indicator indicates that the results in all measured segments are valid. A non-zero value indicates that an error occurred in at least one of the measured segments.

• Seg_Reliability: int: decimal The segment reliability indicates whether one of the following exceptions occurred in this segment: 0: No error 3: Signal overflow 4: Signal low 8: Synchronization error If a combination of exceptions occurs, the most severe error is indicated. Range: 0 | 3 | 4 | 8

• Obw: float: float Occupied bandwidth Range: 0 MHz to 8 MHz (SDEViation 0 MHz to 4MHz) , Unit: Hz

calculate(segment=<Segment.Default: -1>) → CalculateStruct

# SCPI: CALCulate:CDMA:MEASurement<Instance>:MEValuation:LIST:SEGMent<nr>:OBW:AVERage
value: CalculateStruct = driver.multiEval.listPy.segment.obw.average.calculate(segment = repcap.Segment.Default)

Returns occupied bandwidth (OBW) results for the segment <no> in list mode (see method RsCmwCdma2kMeas.Configure. MultiEval.ListPy.value) . To define the statistical length for AVERage, MAXimum and SDEviation calculation and to enable the calculation of the results use the command method RsCmwCdma2kMeas.Configure.MultiEval.ListPy.Segment.Spectrum.set. The ranges indicated below apply to all results except standard deviation results. The minimum for standard deviation results equals 0. The maximum equals the width of the indicated range divided by two. Exceptions are explicitly stated. The values described below are returned by FETCh commands. CALCulate commands return limit check results instead, one value for each result listed below.

param segment

optional repeated capability selector. Default value: Nr1 (settable in the interface ‘Segment’)

return

structure: for return value, see the help for CalculateStruct structure arguments.

fetch(segment=<Segment.Default: -1>) → FetchStruct

# SCPI: FETCh:CDMA:MEASurement<Instance>:MEValuation:LIST:SEGMent<nr>:OBW:AVERage
value: FetchStruct = driver.multiEval.listPy.segment.obw.average.fetch(segment = repcap.Segment.Default)

Returns occupied bandwidth (OBW) results for the segment <no> in list mode (see method RsCmwCdma2kMeas.Configure. MultiEval.ListPy.value) . To define the statistical length for AVERage, MAXimum and SDEviation calculation and to enable the calculation of the results use the command method RsCmwCdma2kMeas.Configure.MultiEval.ListPy.Segment.Spectrum.set. The ranges indicated below apply to all results except standard deviation results. The minimum for standard deviation results equals 0. The maximum equals the width of the indicated range divided by two. Exceptions are explicitly stated. The values described below are returned by FETCh commands. CALCulate commands return limit check results instead, one value for each result listed below.

param segment

optional repeated capability selector. Default value: Nr1 (settable in the interface ‘Segment’)

return

structure: for return value, see the help for FetchStruct structure arguments.